Home / Resources / Galvanizing coating thickness
Hot-Dip Galvanizing Coating Thickness: ISO 1461, ASTM A123, GB/T 13912, AS/NZS 4680 and JIS H 8641 Side by Side
“Galvanized to 85 µm” is not a complete specification. Five national and international systems classify the same steel differently, and the same 3 mm purlin can legitimately be required at 55 µm, 65 µm or 63 µm depending on which standard governs the order. This reference sets the current editions side by side, converts between coating mass and thickness, and works the service-life arithmetic for each corrosivity category.
Thickness is the only part of a galvanizing specification that can be measured, disputed and paid for. Appearance, “full coverage” and “uniform coating” are not quantities. Yet the number alone is ambiguous, because each standard attaches its minimum to a different variable: ISO 1461 and its derivatives key on steel thickness only; ASTM A123 keys on material category and thickness together; JIS moved in 2021 from coating mass to coating thickness and renamed its classes in the process. A purchaser who writes “hot-dip galvanized, 85 µm” without naming the standard has written three different requirements.
The five systems at a glance
| Standard | Title / scope | Basis of classification | Current edition |
|---|---|---|---|
| ISO 1461 | Hot dip galvanized coatings on fabricated iron and steel articles | Steel thickness only | 2022 (supersedes 2009) |
| ASTM A123/A123M | Zinc (hot-dip galvanized) coatings on iron and steel products | Material category × thickness | 2024 (supersedes 2017) |
| GB/T 13912 | Metallic coatings — hot dip galvanized coatings on fabricated iron and steel articles | Steel thickness only | 2020 (supersedes 2002) |
| AS/NZS 4680 | Hot-dip galvanized (zinc) coatings on fabricated ferrous articles | Article thickness; separate table for centrifuged work | 2006 |
| JIS H 8641 | Hot dip galvanized coatings | Coating thickness classes (HDZT), aligned to ISO 1461:2009 | 2021 (supersedes 2007) |
Two further standards sit underneath these and are routinely confused with them. ISO 10684 governs hot-dip galvanized fasteners; ASTM A153/A153M governs hardware. A bolt is not covered by the article standard, and its minimum is lower because the thread has to be tapped oversize afterwards.
Coating thickness by steel thickness
For the ISO-family standards the table is short and the logic is the same: heavier steel holds more zinc because the bath reacts longer with a thicker section. Every system sets two numbers — a local minimum for any single reference area and a mean minimum for the article as a whole. Both must be satisfied; a good mean with one thin patch is a non-conformance.
| Steel thickness | ISO 1461:2022 local / mean |
GB/T 13912-2020 local / mean |
AS/NZS 4680:2006 local / mean |
ISO 1461 mean g/m² |
|---|---|---|---|---|
| < 1.5 mm | 35 / 45 | 35 / 45 | 35 / 45 | ≈320 |
| ≥ 1.5 to ≤ 3 mm | 45 / 55 | 45 / 55 | 45 / 55 | 395 |
| > 3 to ≤ 6 mm | 55 / 70 | 55 / 70 | 55 / 70 | 505 |
| > 6 mm | 70 / 85 | 70 / 85 | 70 / 85 | 610 |
AS/NZS 4680 also carries a second table for centrifuged articles — spun work such as threaded rods, where the spin throws zinc off the threads: 35/45 µm below 8 mm and 45/55 µm above. That is the Australian and New Zealand equivalent of the fastener rule, and it is the number to quote for spun hardware rather than the article table.
ASTM A123-24: the same steel, a different question
ASTM A123 does not ask “how thick is the steel”. It asks “what product is this, and how thick is it”, then reads the answer off a matrix. The practical consequence is that a 5 mm structural shape and a 5 mm tube are held to different minimums — 75 µm and 75 µm in that band, but 100 µm and 75 µm once both pass 6.4 mm.
| Material category | ≤1.6 mm | >1.6–3.2 | >3.2–4.8 | >4.8–6.4 | >6.4–16 | >16 mm |
|---|---|---|---|---|---|---|
| Structural shapes | 45 | 65 | 75 | 75 | 100 | 100 |
| Plate | 45 | 65 | 75 | 75 | 75 | 100 |
| Strip and bar | 45 | 65 | 75 | 75 | 75 | 100 |
| Pipe and tubing | 45 | 45 | 75 | 75 | 75 | 75 |
| Forgings and castings (category added in the 2024 edition) |
100 | 100 | 100 | 100 | 100 | 100 |
Two rules in the 2024 edition matter more than the numbers. First, the one-grade-below tolerance: an individual specimen may fall one coating grade under the table value, and the grades step 35 → 45 → 50 → 55 → 60 → 65 → 75 → 80 → 85 → 100. Second, Annex X1.1 now tells you how to classify a product — a member built from bent or welded plate is plate, not a structural shape. Before that annex, cold-formed C and U sections were classified by argument, and the answer changed the requirement by 10 µm.
Japan and India: two different bases
JIS H 8641:2021 is the clearest example of why edition control matters. The 2007 edition specified coating mass in classes named HDZ 35, HDZ 45 and HDZ 55. The 2021 revision moved to coating thickness measured with an electromagnetic gauge, renamed the classes HDZT, and renumbered them: HDZ 35 became HDZT 49, HDZ 45 became HDZT 63, and HDZ 55 became HDZT 77. A drawing that still says “HDZ 55” against a 2021 order is not wrong by a little — it names a class that no longer exists. The 2021 edition is technically aligned with ISO 1461:2009 as a modified adoption.
IS 4759:1996, the Indian standard for hot-dip zinc coatings on structural steel and allied products, is still specified in coating mass rather than thickness — the structural requirement quoted in the market is 610 g/m² from 5 mm upward, which corresponds to roughly 85 µm. The companion standards are IS 2629 for recommended practice and IS 2633 for coating uniformity. When an Indian enquiry and a European enquiry are compared on the same spreadsheet, one column is in g/m² and the other in µm, and someone has to convert before the comparison means anything.
Why the same 3 mm section gets three different numbers
Take a 3 mm cold-formed purlin quoted to three buyers. Under ISO 1461:2022 the minimum mean is 55 µm. Under ASTM A123-24, classified as strip and bar in the 1.6–3.2 mm band, it is 65 µm. Under JIS H 8641:2021 the nearest class is HDZT 63, about 63 µm. Nothing about the steel changed; three defensible specifications produced a 10 µm spread, which on a 200-tonne order is a real quantity of zinc and a real argument at inspection.
How long the coating lasts: corrosivity, then arithmetic
Thickness only becomes service life once the environment is classified. ISO 12944-2:2017 sorts atmospheres by the first-year thickness loss of standard steel and zinc specimens, and the zinc column is the one that governs a galvanized coating.
| Category | Zinc loss, year 1 (µm) | Steel loss, year 1 (µm) | Typical environment |
|---|---|---|---|
| C1 very low | ≤ 0.1 | ≤ 1.3 | Heated interiors, clean air — offices, schools |
| C2 low | 0.1 – 0.7 | 1.3 – 25 | Rural, low pollution; unheated buildings where condensation occurs |
| C3 medium | 0.7 – 2.1 | 25 – 50 | Urban and industrial, moderate sulphur; low-salinity coast |
| C4 high | 2.1 – 4.2 | 50 – 80 | Industrial areas and coasts with moderate salinity |
| C5 very high | 4.2 – 8.4 | 80 – 200 | High-salinity coast, aggressive industry |
| CX extreme | 8.4 – 25 | 200 – 700 | Offshore, splash zone, tropical marine industrial |
Immersed and buried structures are classified separately as Im1 to Im4 — fresh water, sea or brackish water without cathodic protection, soil, and sea or brackish water with cathodic protection. The 2017 revision also merged the former C5-I and C5-M into a single C5 and added CX, so a specification written before 2017 may cite a category that no longer exists.
With a loss rate, first maintenance is simple division: years ≈ coating thickness ÷ annual zinc loss. The result is a planning range, not a guarantee — the rate is a first-year figure and usually falls as corrosion products build up, and it says nothing about mechanical damage.
| Coating (mean) | C2 | C3 | C4 | C5 | CX |
|---|---|---|---|---|---|
| 55 µm — 1.5–3 mm article | 80 – 550 | 26 – 79 | 13 – 26 | 7 – 13 | 2 – 7 |
| 70 µm — 3–6 mm article | 100 – 700 | 33 – 100 | 17 – 33 | 8 – 17 | 3 – 8 |
| 85 µm — over 6 mm article | 120 – 850 | 40 – 121 | 20 – 40 | 10 – 20 | 3 – 10 |
| 140 µm — grit-blasted before dipping | 200 + | 67 – 200 | 33 – 67 | 17 – 33 | 6 – 17 |
ISO 12944-1:2017 sets four durability tiers rather than three: low up to 7 years, medium 7–15 years, high 15–25 years, and very high beyond 25 years. Note that durability here means time to first maintenance, not the absence of maintenance forever.
When the coating has to last longer than the standard allows
ISO 1461 minimums are designed for the ordinary case. Where the environment or the design life pushes past them, there are four levers, in ascending order of cost:
- Specify a thicker coating by agreement. The standard permits it; the galvanizer needs to know before dipping, because achieving it depends on steel chemistry as much as on process time.
- Grit-blast before galvanizing. A Sa 2½ surface profile opens the steel and typically adds 20–50% pick-up. The practical ceiling is around 140 µm on heavy sections.
- Specify reactive steel deliberately. Silicon above roughly 0.25% grows a thicker, duller, entirely zinc-iron coating, up to about 200 µm on heavy sections. It is harder and more brittle, so handling damage becomes the limiting factor rather than corrosion.
- Go duplex — galvanizing plus a paint system. The total life is not simply the sum of the two; the paint slows zinc consumption and the zinc protects the steel where the paint is damaged. Published guidance puts the duplex synergy at roughly 1.5 to 2.5 times the sum of the individual lives.
Inspection and acceptance: where the arguments actually happen
- Method. Magnetic-induction gauges are the field method (ISO 2178, ASTM E376, ASTM B499). Gravimetric strip-and-weigh and microscopical cross-section are the referee methods when a result is disputed.
- Reference areas. A local reading is the mean of several gauge readings within one reference area, taken away from edges, drips and contact marks. Quoting a single spot reading as “the thickness” is not a measurement under any of these standards.
- Sampling. ISO 1461 fixes the number of control samples by lot size and the number of reference areas by surface area. A one-off gauge reading on one column does not clear a lot.
- Bare spots. The usual acceptance limit is 0.5% of the surface area with no individual spot larger than 10 cm² — and the percentage applies per article or per reference area, depending on the standard, which is exactly the kind of detail that decides a concession.
- Repair. Damaged coating is repaired with zinc-rich paint or sprayed zinc under ASTM A780 or the repair annex of ISO 1461, and the repair is recorded. Unrecorded touch-up is the most common reason a certificate does not match the steel.
- Certificate contents. Standard and edition, lot identification, steel thickness class, local and mean values per reference area, the applicable minimum, and the steel certificate with silicon and phosphorus content where reactive steel was used.
Six specification mistakes that cost money
- Writing “galvanized” without a thickness. There is no default. The default is whatever the galvanizer’s process produces, which may be above the minimum and may not be.
- Mixing a sheet standard with an article standard. Z275 per EN 10346 is a two-face figure; it is not comparable with a per-face article requirement.
- Assuming thicker steel always means a thicker coating. True within a standard’s table, false across standards — ASTM A123 puts 100 µm on heavy structural shapes where ISO 1461 asks 85 µm.
- Citing a withdrawn class or category. HDZ 55 in JIS, or C5-I in ISO 12944, no longer exist. The order should name the edition, not just the number.
- Ignoring silicon and phosphorus. Reactive steel can give 200 µm where 85 µm was wanted, and the coating may be dull and more brittle. It should be a decision, not a surprise.
- Forgetting vent and drain holes. A sealed hollow section cannot be galvanized safely; trapped air or moisture can rupture the section in the bath and leaves the interior uncoated. This is a design responsibility, not a galvanizer’s.
Where to obtain the standards
Each of these bodies publishes the current edition, and each listing states the edition and its superseded predecessors. Editions change; the values in this page were checked against the sources below in November 2026.
- ISO 1461:2022 — ISO
- ASTM A123/A123M-24 — ASTM International
- GB/T 13912-2020 — Standardization Administration of China
- AS/NZS 4680:2006 — Standards Australia
- JIS H 8641:2021 — Japanese Standards Association
- IS 4759 — Bureau of Indian Standards
- CSA G164-18 (R2023) — CSA Group
- American Galvanizers Association — technical library and standard comparisons
- Galvanizers Association (UK) — EN ISO 1461 guidance
Designing to more than one code set?
The companion reference maps the design side of the same problem — AISC 360, CSA S16, EN 1993, GB 50017, IS 800 and AS 4100 side by side, with loading, cold-formed, welding and bolting standards for each market.
Steel building design codes by country →
If you are specifying a galvanized frame for a coastal or industrial site and want the coating clause written into the enquiry, send the project location, the design life and the governing standard — we will return a coating specification with the thickness, the standard edition and the inspection regime stated.
Sources and verification note
- ISO 1461:2022 thickness table and coating mass values; ISO 12944-2:2017 corrosivity categories and zinc loss rates; ISO 12944-1:2017 durability tiers — as reproduced in Galvanizers Association (UK) and Nordic Galvanizers technical guidance, checked November 2026.
- ASTM A123/A123M-24 category matrix, one-grade-below rule and Annex X1.1 classification guidance; ASTM A780 repair; ISO 10684 and ASTM A153 scope — ASTM International and American Galvanizers Association publications.
- GB/T 13912-2020 thickness grades, stated as a modified adoption of ISO 1461:2009.
- AS/NZS 4680:2006 Tables 1 and 2, including the centrifuged-work table.
- JIS H 8641:2021 revision history, the HDZ to HDZT class conversion and its ISO 1461:2009 (MOD) relationship — Japanese Standards Association edition notice.
- IS 4759:1996 coating mass requirement and companion standards IS 2629 and IS 2633.
- CSA G164-18 (R2023), fourth edition, 2018, reaffirmed 2023, with the scope focused on electrical and communication hardware.
- Duplex system synergy of roughly 1.5–2.5× — published duplex guidance referenced by the galvanizing associations.
Last verified: 16 November 2026. Standards are revised; confirm the edition on the publisher’s page before writing it into a contract. This page is a cross-reference for specification and study, not a substitute for the standards themselves.