مصنع دقيق بمساحة 15,000 متر مربع، كينيا
A single roof over milling, packing and bagged storage keeps grain intake and flour dispatch on one continuous production floor in Kenya.
بيانات المشروع
Facts a contractor checks first: Flour milling and grain storage - Low-pitched multi-bay portal frames with attached milling tower, 15,000 m² under roof, four silos and one domed bin.
| Industry | Flour milling and grain storage - intake, milling, packing and bagged dispatch on one site |
|---|---|
| Construction type | Low-pitched multi-bay portal frames with attached milling tower - misty blue-grey cladding, silver-grey roofs, navy accents |
| Project scale | 15,000 m² under roof, four silos and one domed bin - 1,280 t of fabricated structural steel |
| Location | Inland industrial zone, Kenya - dry bright highland climate, reddish earth, seasonal dust |
| Collaborators | Milling-line supplier · local civil works - frame set around the grain intake and silo sequence |
| التسليم | 39 weeks on site - milling tower commissioned before the warehouse handover |
| Our scope | Structural design and 3D modelling · multi-bay portal frames · attached milling tower frame · secondary steel and bracing · roof sheeting with ventilated ridge caps · wall cladding and trims · silo support steel and transfer gantries · gutters and downpipes · erection drawings and site support |
نظرة عامة على المشروع
A flour mill only runs as well as the route grain takes through it.
SynJect supplied 1,280 tonnes of structural steel for a 15,000 m² flour factory and warehouse in Kenya, built around one continuous low-pitched roof that covers milling, packing and bagged storage. Grain intake, the milling tower and dispatch sit under the same weather line, so product never crosses an open yard.
The frame follows the grain flow. Four galvanized silos and a domed bin stand beside the tall milling tower, with transfer gantries running between them, while the wide warehouse bays carry the packing and pallet lines at floor level.
The highland Kenyan site drives the detailing: ventilated ridge caps that purge heat and fine flour dust, sealed light-coloured cladding against seasonal dust, and galvanized steel on every exposed gantry, stair and silo support.

أربعة قرارات حاسمة
One Weather Line
Milling, packing and storage share a single roof, so grain never crosses an open yard.
Silos Beside The Mill
Four silos and a domed bin feed the tower through short transfer gantries.
Ventilated Ridge
Ridge caps purge heat and fine flour dust without adding roof penetrations.
Dust-Sealed Envelope
Sealed light-coloured cladding and covered transfers suit a dry, dusty highland site.
المشروع كما تم تنفيذه
The same plant seen from the air, at eye level, and during steel erection.






شهادة العميل
Feedback from Mill Project Manager after handover.

The silos, the tower and the packing hall were always going to be one building. Having a single frame package meant the transfer gantries lined up first time.
الأسئلة الشائعة
Common questions from buyers specifying this building type.
How is a 15,000 m² flour factory in Kenya quoted?
A 15,000 m² flour factory in Kenya is quoted against an itemised bill of quantities rather than a flat rate per square metre, because bay spacing, eave height, the attached milling tower, silo support loads, wind and dust assumptions, coating specification and delivery distance all change the steel tonnage that SynJect has to fabricate. The BOQ separates primary frames, secondary steel, roof and wall sheeting, gantries, trims, fasteners and coatings so each line can be compared between bidders. Send SynJect the process layout, eave height, silo schedule and site location and the quantities come back itemised against those inputs.
What is included in the steel package for a flour mill — and what is not?
The steel package for the 15,000 m² flour factory in Kenya covers structural design and 3D modelling, the multi-bay portal frames, the attached milling tower frame, secondary steel and bracing, roof sheeting with ventilated ridge caps, wall cladding with navy trims and the silo transfer gantries as one coordinated supply. Earthworks, foundations, the floor slab, silos themselves, milling equipment, dust extraction and utilities sat outside that package on this project. The table below shows the boundary as it was applied on the delivered mill. In the steel package Outside the package Portal frames, tower frame, bracing, secondary steel Earthworks, foundations and ground-floor slab Roof sheeting, wall cladding, ridge caps, trims Grain silos, milling lines and dust extraction Silo support steel and transfer gantries Electrical, plumbing and fire services 3D model, shop drawings and erection drawings Local erection labour, cranes and permits
Which design codes and documentation apply to a steel flour mill in Kenya?
A steel flour mill in Kenya is designed to the local authority load requirements together with internationally recognised steel design standards for the frames, connections and coatings. For the delivered 15,000 m² plant, the design basis recorded the highland wind exposure, seasonal dust load, silo support reactions and the thermal movement assumed across the long roof runs. Every SynJect project is modelled in 3D before fabrication, so connection schedules and code checks stay traceable from model to shop drawing. Ask for the design basis report with the BOQ and the assumptions are visible before cutting starts.
How are fabrication, shipping and erection sequenced for a Kenya mill project?
Fabrication, shipping and erection for a Kenya mill project run as one coordinated sequence: SynJect fabricates and trial-assembles the frames at the works, ships members in erection order, and hands the site team a crane study plus marked erection drawings before the first lift. On this plant, the milling tower frame went up first so the transfer gantries could be aligned to the silo positions early. The sequencing plan, crane study and erection drawings are part of the SynJect package, so local contractors price lifts against drawings.
How is combustible flour dust handled in the building design?
Combustible flour dust in the delivered Kenya mill is handled by the building envelope and the roof detailing: ventilated ridge caps purge fine dust and heat at the highest point, sealed wall and roof junctions prevent dust lodging in cavities, and covered transfer gantries keep product out of the open air between the silos and the tower. Dust extraction equipment and explosion relief panels belong to the process package, but their positions were reserved in the 3D model before fabrication. Ask for the interface drawing set with the BOQ and the steel-to-process boundary becomes unambiguous.
Why put four silos and a domed bin beside the milling tower?
Four galvanized silos and one domed bin beside the milling tower suit a 15,000 m² flour plant because grain can be segregated by batch without long horizontal conveying runs. Short transfer gantries between the silos and the tower cut both conveying energy and the number of places where dust can escape into the production hall. Silo support reactions were fed into the frame model as point loads, so the adjacent portal bays and their bracing were sized for those loads from the start. A later silo addition is possible, but only if its load case is included in the first design basis rather than added afterwards.
Who is responsible for the floor slab under milling and packing lines?
The ground-floor slab under milling and packing lines sits outside the SynJect steel package and is poured by the local civil contractor against our hold-down details. On the Kenya plant, milling equipment loads, joint layout, flatness class and silo foundation interfaces were agreed between the two packages before the slab was specified. The milling equipment sets those tolerances, not the frame, so the line supplier has to sign them off early. Request the interface drawing set with the BOQ and the steel-to-slab boundary becomes unambiguous.
What does the 15,000 m² figure cover on this Kenya flour factory?
The 15,000 m² figure covers everything under roof on the delivered project in Kenya: the milling hall, the packing and palletising bays, the bagged-storage warehouse and the covered transfer routes between them. External silos, the domed bin, yard roads, truck aprons and drainage are excluded from that number. Quoting area this way makes bids directly comparable, because one supplier cannot hide the tower footprint outside the total. Ask any bidder to split hall, warehouse and tower areas in the same manner before comparing tonnages.
Why a low-pitched roof with ventilated ridge caps on this mill?
The low-pitched roof on this Kenya flour factory keeps the enclosed volume tight while the ventilated ridge caps release heat and fine flour dust at the highest point of each bay. Short, even roof falls also keep gutter runs clear of the transfer gantries and away from the silo loading points. A steep roof would add unheated volume above the milling lines without adding usable floor space. Ridge cap positions were fixed in the 3D model before fabrication, so they never clash with purlins or bracing.
Can the warehouse bays be extended later, and how was the frame set out for it?
The Kenya warehouse bays can be extended by repeating another portal bay beyond the packing hall, because the end frame was detailed as a removable future-extension frame rather than a permanent braced wall. Roof sheeting, cladding profile and purlin centres all run to the same grid, so a new bay continues the envelope without a step in the roof line. SynJect recorded the extension assumptions in the design basis, including the extra bay load and the future downpipe position. Confirm the extension bay in the first BOQ and the end-frame connections are fabricated ready for it.
احصل على قائمة الأعمال المطلوبة وخطة التكاليف على مدار 24 ساعة
اكتشف مقدار ما يمكنك توفيره من حمولة الصلب والشحن البحري قبل بدء عملية التصنيع
تخفيض وزن الفولاذ
1:1 تعمل النمذجة ثلاثية الأبعاد باستخدام برنامج Tekla على تحسين نسب العوارض والأعمدة للتخلص من التكاليف الزائدة للمواد.
التحقق من الكود الخالي من التضارب
تم التحقق من مطابقتها لمعيار EN 1090 والأحمال المحلية الناتجة عن الرياح والزلازل.
مراجعة من مهندس إلى مهندس
تم التحقق من صحة هذه المعلومات من قِبل كبار مهندسينا — لا مكالمات مبيعاتية مزعجة على الإطلاق، بل بيانات قابلة للتطبيق وأسعار المصنع فقط.
CE EN 1090-1•ISO 9001•ISO 14001•ISO 45001
المهندسون الرئيسيون عبر الإنترنت
🔒 خصوصية وأمان بنسبة 100٪، بدون رسائل غير مرغوب فيها